显示标签为“toolshop”的博文。显示所有博文
显示标签为“toolshop”的博文。显示所有博文

2014年7月13日星期日

How to Clean Chromed Plastic on Vehicles


How to Clean Chromed Plastic on Vehicles

·                               Chromed plastic is found on many locations of a vehicle such as grills, door handles and body mouldings. It becomes water spotted, can be discolored from acid rain or covered in bug residue. Using a glass cleaner to remove these contaminants is the safest way to clean the plastic without harming the adjacent painted areas. This process can be repeated as needed. However, since the glass cleaner dries to a spotless finish, usually no further cleaning is necessary. 

Instructions

1
Mix a bucket of soapy water using dish detergent and water as if preparing to hand-wash a car. Use the mixture with a kitchen sponge to clean the moulding of all road film and grime. Dry when complete with a chamois or kitchen-type towel.
2
Apply glass cleaner such as Windex to a kitchen towel or directly onto chrome and scrub chromed area with the kitchen towel. Chrome does not scratch easily, so use moderate pressure to scrub stains.
3
Repeat as necessary. Due to the majority of stains, such as tree sap or acid rain spots, being water-based contaminants, a water-based cleaner such as Windex is the best for cleaning. Although glass cleaner should remove all stains, rubbing compound with a terry cloth rag and elbow grease may be used for removing more difficult stains such as dried bird droppings or bug residue.


2014年6月2日星期一

Steps of Injection Molding


Steps of Injection Molding

·                                  
Many popular plastic items are produced by injection molding.
Injection molding has continued to grow since the late 19th century. Capable of producing small items such as combs, it is also used to create parts for airplanes and medical supplies. It is hard to imagine the world without the products it produces. The process was patented by John Wesley Hyatt and his brother Isaiah in 1872. Today, injection molding is used to produce about 30 percent of all plastic products. The process is relatively simple, but expensive. Thus it is usually only used to mass produce items.

Instructions


1
Clamp the mold shut. This will hold the mold in place while the mold is filled with melted plastic. It will also keep the mold still while the plastic cools.
2
Inject the melted plastic into the mold. The plastic starts out as polymer resin pellets which are poured into a large open-bottomed hopper. A motor turns the auger, feeding the pellets into the cylinder where they are melted and turned into molten plastic, then pushed into the mold. The auger injects the melted plastic into the mold at a pressure between 10,000-30,000 pounds per square inch. The auger then holds the plastic, forcing more plastic in to fill the mold completely. This guarantees that the final product will not contain any gaps. A gate closes keeping the plastic inside the mold while it cools. Molds are usually either water ic belting. 35+ years' experience.
3
Drill small holes into the mold, if it is cooled by water or another liquid. The cooling period accounts for about 85 percent of the molding process. The temperature of the water is usually between 33 and 60 degrees Fahrenheit. Water below freezing can be used. However, glycol, or a similar additive, needs to be used to keep the water from freezing. The major disadvantage to using water to cool the mold is the buildup of condensation.
4
Loosen the clamp and open the mold. Remove the plastic part that was just created. Then clean the part, removing any excess plastic.


2014年5月27日星期二

Research and Forecast of Injection Molding Machine Industry in China, 2014-2018


Research and Forecast of Injection Molding Machine Industry in China, 2014-2018


The injection molding machine belongs to the plastic machinery type that has the largest output and application volume in China, as well as being the main force of China's plastic machinery export. In 2013, the export volume of injection molding machines was 22,946 sets with the export amount of USD 932 million; in 2012, the export volume was 24,830 sets, so the export volume in 2013 declined, but the export value in 2013 increased 3.78%, which fully shows that the average price of export products of China's injection molding machines is gradually growing. With the increasing demand for plastics, plastic machinery industry has huge market potential. From the global perspective, the top three plastic machinery types are injection molding machine, extruder/extruder production line and blowing molding machine, which account for more than 80% in the plastic machinery total output value. Among them, injection molding machine accounts more than 50% of the total output value of these three main types of plastic machines. 

In 2013, the output of China's injection molding machines was about 82,000 sets, rising by 4.21% compared with 2012. On the whole, the growth of China's injection molding machine industry gradually slowed during the year of 2007 to 2013, but the output was still rising. During 2007 to 2013, the average growth rate of output of China's injection molding machines was 4.77%. 

As this report estimates, the market supply volume of China's injection molding machines will reach 86,175 sets by 2014, 89,612 sets by 2015 and about 101,095 sets by 2018


http://www.freetech-mould.com


2014年5月4日星期日

key point of injection mold design (2/2)


  2.8 one hinge

2.8.1  for PP material toughness, can be designed hinge and product to be an integration.

2.8.2 as a film hinge should be less than the size of 0.5mm, and to maintain a uniform ,

2.8.3 When integrally injection hinge design, the gate only can be designed at one side of the hinge .

 

  2.9 inserts

2.9.1 In the injection molding ,inserts increase the local strength , hardness, dimensional accuracy and setting small screw holes ( shaft )  to meet a variety of special needs. Will also increase the cost of the product .

2.9.2 Insert typically may be copper ,or other metal and plastic.

2.9.3 insert embedded in the plastic part should stop rotation and anti- pull design structure . Such as: knurled , holes , bending, flattening and so on.

2.9.4 insert should be appropriately thick plastic around to prevent stress cracking of plastic parts .

2.9.5 design inserts, should fully consider the positioning in the mold ( holes , pins, magnetic )

 

  2.10 logo

   Product identification is generally set in the relatively flat surface of the product , and the use of convex form , select the consistent face of mold opening, or may cause the part injury .

 

  2.11 precision injection molded parts

  Due to heterogeneity and uncertainty injection shrinkage , significantly lower than the metal injection molding precision parts, should Select the appropriate standard tolerances (OSJ1372-1978)

 

  2.12 deformation of injection molded parts

  Improve the rigidity of the injection of product structure, reduce deformation . Try to avoid flat structure , a reasonable set of cuffs , uneven structure. Set reasonable reinforce ribs .

 

 2.13 GAIM

2.13.1 using gas-assisted injectionmolding, can improve product rigidity and reduce distortion.

2.13.2 using GAIM avoid sink mark.

2.13.3 using gas-assisted injection molding, can save raw materials, shorten the cooling time .

 

  2.14 welding ( hot plate welding, ultrasonic welding , vibration welding )

2.14.1 welding , can improve the coupling strength.

2.14.2 welded to simplify product design.

 

3 . Reasonable to consider the contradiction between process and product performance

Must be integrated into contradiction product appearance , performance and design of injection molding processes Sometimes sacrifice some process to get a good appearance or performance.

3.1 if sometimes mold design can not avoid injection defect, try to design and make the defect on the hidden place of the parts.

 

 

Injection molding design points

1 , the direction of mold open and mold parting line

2 , draft angle

3 , thickness of the part wall

4 .ribs

5 , chamfer, rounded corners and holes

6 , core-pulling mechanism and avoid

7 , plastic deformation

8 , one hinge

9 , insert

10 , GAIM

11 , considering the technology and performance parts


Professional Tool Maker in China  http://www.freetech-mould.com